Get this stance - 3 inch drop.
Get this stance - 3 inch drop.
3” Lowered Stance - An Entry Level to slammed society.
With minimal tools you can bolt the parts into your car and be riding lower with style.
Disclaimer
Please read the instructions completely before starting.
All instruction is provided to enable correct fitment of these products and should only be undertaken by an individual with sound mechanical knowledge.
Use only the mounting hardware provided.
If you are unclear about any of the instruction steps do not continue until you have made contact with Fresh Kustoms Technical Support. technical@freshkustoms.com
No warranty shall be entered into if this procedure is not followed.
Type 2 Late Baywindow
Lowered spindles discbrakes, as pair
Models: Type 2 Early Baywindow, Type 2 Late Baywindow
Model Details: Bus 08/72-07/79
Part no. SQ1384-500
If you own a Late Bay Window Bus then this system is for you. Rear drop plates to suit Late Bay window Bus.
Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come.
With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory.
Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre.
Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions.
Height settings
3” Raise, Stock Height, 3”, 6” and 9” drop from the factory height
Note: 3” Raise and 9” Drop will require additional vehicle modifications
Models: Type 2 Late Baywindow
Part no. SQ1583359
Type 2 Early Baywindow
Lowered spindles discbrakes, as pair
Models: Type 2 Early Baywindow, Type 2 Late Baywindow
Model Details: Bus 08/72-07/79
Part no. SQ1384-500
If your type 2 split window Bus has been converted to use a long axle gearbox from a beetle or type 3 then this system is for you Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come. With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory. Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre. Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions. Looking to upgrade later to Split IRS or change back to stock reduction boxes? This is easily done with the FK Drop Plate System, re-use your existing modified spring plates as the adjustment holes are the same profile for all three FK Plate designs. Height settings 4.5" and 7.5" drop from the factory height
Models: Type 2 Splitwindow
Part no. SQ7688012
Type 2 Splitwindow
If your type 2 Split window Bus has been converted to use IRS then this system is for you Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come. With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory. Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre. Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions. Looking to change your Split Window Bus back to straight axle or stock reduction boxes? This is easily done with the FK Drop Plate System, re-use your existing modified spring plates as the adjustment holes are the same profile for all three FK Plate designs. Height settings 1.5”, 4.5" and 7.5" drop from the factory height
Models: Type 2 Splitwindow
Part no. SQ0262726
If your type 2 split window Bus is still running its original Reduction Gear Boxes then this system is for you Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come. With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory. Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre. Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions. Looking to upgrade later to Straight Axle or Split IRS? This is easily done with the FK Drop Plate System, re-use your existing modified spring plates as the adjustment holes are the same profile for all three FK Plate designs. Height settings 1.5", 4.5" and 7.5" drop from the factory height;
Models: Type 2 Splitwindow, Type 2 Early Baywindow, Type 2 Late Baywindow
Part no. SQ4676440
Lowered spindles for brake drums;as pair
Models: Type 1 Beetle, Type 14 Karmann Ghia
Model Details: Beetle, Karmann Ghia -07/65
Part no. SQ1380-1