Get This Stance - 6" DROP -
Get This Stance - 6" DROP -
6” Lowered Stance - A Step Up in Slamming Suspension.
This look can be achieved without any modification to your chassis.
Disclaimer
Please read the instructions completely before starting.
All instruction is provided to enable correct fitment of these products and should only be undertaken by an individual with sound mechanical knowledge.
Use only the mounting hardware provided.
If you are unclear about any of the instruction steps do not continue until you have made contact with Fresh Kustoms Technical Support. technical@freshkustoms.com
No warranty shall be entered into if this procedure is not followed.
Type 2 Baywindow
(1) FK Drop Plate Kit
Type 2 Early Baywindow
Type 2 Late Baywindow
If you own a Late Bay Window Bus then this system is for you. Rear drop plates to suit Late Bay window Bus.
Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come.
With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory.
Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre.
Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions.
Height settings
3” Raise, Stock Height, 3”, 6” and 9” drop from the factory height
Note: 3” Raise and 9” Drop will require additional vehicle modifications
Models: Type 2 Late Baywindow
Part no. SQ1583359
If your type 2 split window Bus has been converted to use a long axle gearbox from a beetle or type 3 then this system is for you Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come. With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory. Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre. Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions. Looking to upgrade later to Split IRS or change back to stock reduction boxes? This is easily done with the FK Drop Plate System, re-use your existing modified spring plates as the adjustment holes are the same profile for all three FK Plate designs. Height settings 4.5" and 7.5" drop from the factory height
Models: Type 2 Splitwindow
Part no. SQ7688012
(2) FK Baywindow Beam
Left Hand Drive
Right Hand Drive
Available for Pre Order
Fresh Kustoms Type 2 Narrowed and Adjustable Ball Joint beams are made from the finest materials.
Our tube is custom made from high grade steel then laser cut to ensure strength and accuracy.
Quality laser cut side plates in 10mm thickness with beam/chassis position mounting holes of stock location and 40mm raised (notching required) to the chassis for both split and bay chassis mounting hole configurations, these ball joint beams will fit any bus 55-79.
Each beam comes fitted with a pivot steering stop plate, brake booster bracket and steering damper mount.
Equipped with our new style Fresh Kustoms Beam Adjusters with long range tooth adjustment offering more adjustability than ever before you will get the stance of your car just where you want it.
What’s included;
Brand new Fresh Kustoms Premium Inner Composite Bushes (fibre outer with copper and teflon coated inner) to match the original factory produced bushes, this style of bush have lasted more than 50 years
Brand new outer needle roller bearings
Brand new Fresh Kustoms heavy duty steering pivot housing supplied with new steering pin assembly (pin bushes and seals supplied)
Brand new grease nipples
All beams are finished in satin black etch primer as standard with other coating options available in black powder coat or silver zinc electroplating at additional cost, you can choose these option.
All beams up to 4 inch narrowed have a one piece side plate and shock tower design.
All beams 5″ or narrower have the side plates mounted inside the chassis rails and the shock towers mounted outside of the chassis rails so these beams will have a two piece side plate/shock tower assembly (all necessary hardware supplied) these kits also come with the 40mm raised beam chassis notch weld in profile and lower shock offset plates this type of kit is perfect for running low with wide wheels on the front.
This product will fit a Splitwindow Kombi.
Please choose the desired narrowed width, coating option and supply of new narrowed torsion leave/spring packs and tie rod assemblies to match you beam before adding to the item to your cart.
Reminder - this product is for right hand drive vehicles
Models: Type 2 Splitwindow, Type 2 Early Baywindow, Type 2 Late Baywindow
Part no. SQ3250616
Available for Pre Order
Fresh Kustoms Type 2 Narrowed and Adjustable Ball Joint beams are made from the finest materials.
Our tube is custom made from high grade steel then laser cut to ensure strength and accuracy.
Quality laser cut side plates in 10mm thickness with beam/chassis position mounting holes of stock location and 40mm raised (notching required) to the chassis for both split and bay chassis mounting hole configurations, these ball joint beams will fit any bus 55-79.
Each beam comes fitted with a pivot steering stop plate, brake booster bracket and steering damper mount.
Equipped with our new style Fresh Kustoms Beam Adjusters with long range tooth adjustment offering more adjustability than ever before you will get the stance of your car just where you want it.
What’s included;
Brand new Fresh Kustoms Premium Inner Composite Bushes (fibre outer with copper and teflon coated inner) to match the original factory produced bushes, this style of bush have lasted more than 50 years
Brand new outer needle roller bearings
Brand new Fresh Kustoms heavy duty steering pivot housing supplied with new steering pin assembly (pin bushes and seals supplied)
Brand new grease nipples
All beams are finished in satin black etch primer as standard with other coating options available in black powder coat or silver zinc electroplating at additional cost, you can choose these option.
All beams up to 4 inch narrowed have a one piece side plate and shock tower design.
All beams 5″ or narrower have the side plates mounted inside the chassis rails and the shock towers mounted outside of the chassis rails so these beams will have a two piece side plate/shock tower assembly (all necessary hardware supplied) these kits also come with the 40mm raised beam chassis notch weld in profile and lower shock offset plates this type of kit is perfect for running low with wide wheels on the front.
This product will fit a Splitwindow Kombi.
Please choose the desired narrowed width, coating option and supply of new narrowed torsion leave/spring packs and tie rod assemblies to match you beam before adding to the item to your cart.
Reminder - this product is for right hand drive vehicles
Models: Type 2 Splitwindow, Type 2 Early Baywindow, Type 2 Late Baywindow
Part no. various
(3) Tires / Wheels
DIY
The DIY Type 2 Ball Joint beam kit has been put together for those who would prefer to make their original kombi beam adjustable and narrowed for that lower tucked stance The kit consists of all the items you need to modify the original beam - Two new 10mm laser cut side plates that allow for the beam to mount into a split or bay window kombi - Two Avis style beam adjusters - Two new 10mm FK logo gussets for additional tube to side plate strength Kit comes with instructions Installing this kit requires welding
Models: Type 2 Early Baywindow, Type 2 Late Baywindow
Part no. SQ0076836
At A 6” Drop and Lower, smaller tires will need to be fitted.
Fresh Kustoms can supply whatever tires and wheels your desired stance requires.
Type 2 Splitwindow
(1) FK Drop Plate Kit
Independant Rear Suspension
Reduction Gear Box
Axle
If your type 2 Split window Bus has been converted to use IRS then this system is for you Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come. With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory. Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre. Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions. Looking to change your Split Window Bus back to straight axle or stock reduction boxes? This is easily done with the FK Drop Plate System, re-use your existing modified spring plates as the adjustment holes are the same profile for all three FK Plate designs. Height settings 1.5”, 4.5" and 7.5" drop from the factory height
Models: Type 2 Splitwindow
Part no. SQ0262726
If your type 2 split window Bus is still running its original Reduction Gear Boxes then this system is for you Laser cut from quality high tensile steel plate and then zinc coated, our FK Drop Plates will still look good for years to come. With some easy drilling and cutting modification to your original spring plates, our bolt in plate system will provide a pre tensioned ride like factory. Run wide rubber on the rear of your bus and get it down low with out completely dismantling the rear end of your bus to change a flat tyre. Each kit comes with two drop plates, two cap spacers, fitting hardware and installation instructions. Looking to upgrade later to Straight Axle or Split IRS? This is easily done with the FK Drop Plate System, re-use your existing modified spring plates as the adjustment holes are the same profile for all three FK Plate designs. Height settings 1.5", 4.5" and 7.5" drop from the factory height;
Models: Type 2 Splitwindow, Type 2 Early Baywindow, Type 2 Late Baywindow
Part no. SQ4676440
(2) FK Splitwindow Beam
The DIY Type 2 Split Window beam kit has been put together for those who would prefer to make their original kombi beam adjustable and narrowed for that lower tucked stance
The kit consists of all the items you need to modify the original Split Window beam - Two new 10mm laser cut side plates that allow for the beam to mount into a split or bay window kombi - Two Avis style type 2 beam adjusters - Two new 10mm FK logo gussets for additional tube to side plate strength Kit comes with instructions Installing this kit requires weldingModels: Type 2 Splitwindow
Part no. SQ3357352
(3) Tires / Wheels
At A 6” Drop and Lower, smaller tires will need to be fitted.
Fresh Kustoms can supply whatever tires and wheels your desired stance requires.